新型硫酸铝-壳聚糖助滤剂强化砂滤效能研究

将硫酸铝和壳聚糖复配作为微絮凝助滤剂（AS-CTS）,考察其强化过滤性能.利用分子量分级、荧光光谱等手段分析有机物的去除特性,通过Zeta电位、絮体粒径、分形维数的变化分析其强化过滤机理.结果表明：AS-CTS较AS、CTS强化过滤效果明显,在AS/CTS复配比为2：1、CTS投加量0.3mg/L,转速300r/min,搅拌时间2min的条件下,砂滤出水浊度能达到0.1NTU、颗粒物125个/mL,残余铝浓度0.02mg/L;浊度和颗粒物去除率较未加AS-CTS分别提高了58%、61.7%.AS-CTS强化过滤可有效去除分子量>30KDa的腐殖酸和1~3KDa间的色氨酸类蛋白、溶解性微生物代谢产物、类富里酸.AS-CTS主要靠高分子吸附架桥作用和界面化学作用,增加胶体颗粒在滤料表面的粘附;通过形成较大粒径和分形维数的微絮体,增强絮体向滤料表面的迁移.     

碳源对O/A-F/F模式积累内源聚合物及反硝化的影响

好氧/缺氧-盛宴/饥饿(O/A-F/F)选择模式能够在好氧段实现活性污泥积累内源聚合物的同时在缺氧段原位利用内源聚合物驱动反硝化.为了深入探究不同的碳源类型对O/A-F/F模式下内源聚合物积累和内源反硝化的影响,实验以乙酸和葡萄糖为主要碳源探究内源聚合物积累和内源反硝化特性以及富集的活性污泥菌群的结构和功能.结果表明,在O/A-F/F选择模式下,当进水化学需氧量(COD)为500 mg·L~(-1)左右时,以乙酸为主要碳源系统(Ac-SBR)和以葡萄糖为主要碳源的系统(Gc-SBR)均能实现40 mg·L~(-1)的硝酸盐氮的内源去除,且各系统均实现了部分短程反硝化.但Ac-SBR实现了更高的亚硝酸盐的积累.乙酸有利于内源聚羟基脂肪酸酯(PHA)积累并驱动内源反硝化过程,PHA产率为0.52,平均反硝化速率(DNR)为9.65 mg·(L·h)-1.Gc-SBR系统能够实现PHA和糖原(Gly)的同时积累,但Gly产率高于PHA产率,分别为0.36和0.17,DNR为4.35 mg·(L·h)-1.Gly是实现内源反硝化过程的主要驱动力,反硝化脱氮贡献率占总量的77%.16S rRNA高通量测序表明Proteobacteria门中的β-Proteobacteria在Ac-SBR中为优势菌纲,菌群丰度为40.56%,而在Gc-SBR中菌群丰度为18.05%.α-Proteobacteria可能在Gc-SBR中贡献了微生物的糖原积累.β-Proteobacteria、Unclassified Bacteroidetes和Lgnavibacteria在Ac-SBR中贡献了内源PHA积累.     

Sustainable method towards magnetic ordered mesoporous polymers for efficient Methylene Blue removal

The difficulty in achieving high removal efficiency for contaminants in textile wastewater over a wide range of pH impedes the progress of its treatment technique greatly. Herein, a facile and sustainable strategy was adopted for constructing magnetic ordered mesoporous polymers (M-OMPs) without the assistance of organic solvent and catalyst. The prepared M-OMPs were endowed with high special surface area and good superparamagnetism simultaneously, and exhibited high removal efficiency (>99%) for Methylene Blue (MB) within a short time (10 min) at a concentration of 50 mg/L. What's more, high removal efficiency was achieved over a wide range of pH 2-12 and the adsorption capacity for MB on M-OMPs was substantially retained even after 5 adsorption-desorption cycles, further demonstrating the application potential of M-OMPs in the decontamination of textile wastewater.     

Contribution of Pendant Ester Group Hydrolysis to the Erosion of Acrylic Polymers in Binders Aimed at Organotin-Free Antifouling Paints

Specific polymeric material applications as bioactive molecules delivery systems involve a strictly controlled degradation of polymer matrixes. One possibility to obtain a zero-order kinetic for small molecules release consists in a simple hydrolysis of ester groups contained in the macromolecular structure. The chemical degradation can lead to the continuous surface erosion of the formulated resins without loss of their mechanical properties and to a permanent activity of the delivery systems. Hydrolysis is a very well-known reaction in the case of organic molecules containing ester groups. The mechanism seems to be more complicated when ester groups are located in macromolecular structures. With the aim of antifouling applications, acrylic acid polymers bearing lateral ester groups of different chemical structures (hydrophilic, hydrophobic, hydrolyzable) have been prepared, characterized, and immersed in water, at pH 8, and their hydrolysis has been studied. Experimental data display two parameters, at least, which must be taken into account: the reactivity of the ester groups toward hydrolysis and the hydrophilic/hydrophobic balance of the polymer. The susceptibility of the acrylic polymers to hydrolysis has been compared to the erosion characteristics of the corresponding films. The results confirm that hydrolysis is necessary to obtain a regular degradation of the films without loss of mechanical properties. A relationship has been observed between the characteristics of hydrolysis and erosion for each studied polymer.     

供水管网生物膜有机物的二氯乙腈与二氯乙酰胺生成特性

在饮用水输配系统中,来源于管壁生物膜的有机物可能耗氯并生成消毒副产物(DBPs),包括二氯乙腈(DCAN)与二氯乙酰胺(DCAcAm)等高毒性含氮DBPs(N-DBPs).研究考察管网常见的细菌与其胞外聚合物(EPS)以及模拟管壁生物膜氯化与氯胺化后DCAN与DCAcAm的生成,并与天然有机物(NOM)和水源水有机物进行比较.结果显示,铜绿假单胞菌、恶臭假单胞菌与藤黄微球菌与氯反应生成的DCAN、DCAcAm浓度分别为1.48～2.02、0.21～0.38μg·mg~(-1)(mg~(-1)以TOC计),高于同反应条件下NOM的生成量;相比于氯化反应,3株细菌细胞氯胺化生成的DCAN与DCAcAm浓度明显更低.3株菌的EPS也是氯与氯胺化反应生成DCAN与DCAcAm的前体物,且其氯胺化反应生成的DCAcAm浓度高于氯化反应生成的.与NOM、水源水相比,模拟管壁生物膜氯化后生成的N-DBPs与三氯甲烷(TCM)浓度比更高,表明生物膜有机物比NOM与水源水有机物更倾向生成DCAN与DCAcAm类N-DBPs,且模拟管壁生物膜氯胺化的DCAcAm生成量高于氯化反应的,说明管壁生物膜有机物是供水管网系统中DCAN与DCAcAm类N-DBPs的重要前体物.     

Potential applications of porous organic polymers as adsorbent for the adsorption of volatile organic compounds

Volatile organic compounds (VOCs) with high toxicity and carcinogenicity are emitted from kinds of industries, which endanger human health and the environment. Adsorption is a promising method for the treatment of VOCs due to its low cost and high efficiency. In recent years, activated carbons, zeolites, and mesoporous materials are widely used to remove VOCs because of their high specific surface area and abundant porosity. However, the hydrophilic nature and low desorption rate of those materials limit their commercial application. Furthermore, the adsorption capacities of VOCs still need to be improved. Porous organic polymers (POPs) with extremely high porosity, structural diversity, and hydrophobic have been considered as one of the most promising candidates for VOCs adsorption. This review generalized the superiority of POPs for VOCs adsorption compared to other porous materials and summarized the studies of VOCs adsorption on different types of POPs. Moreover, the mechanism of competitive adsorption between water and VOCs on the POPs was discussed. Finally, a concise outlook for utilizing POPs for VOCs adsorption was discussed, noting areas in which further work is needed to develop the next-generation POPs for practical applications.     

Effect of environmental parameters on the degradability of polymer films in laboratory-scale composting reactors

Previous research in our laboratory reported a convenient laboratory-scale composting test method to study the weight loss of polymer films in aerobic thermophilic (53°C) reactors maintained at a 60% moisture content. The laboratory-scale compost reactors contained the following synthetic compost mixture (percentage on dry-weight basis): tree leaves (45.0), shredded paper (16.5), food (6.7), meat (5.8), cow manure (17.5), sawdust (1.9), aluminum and steel shavings (2.4), glass beads (1.3), urea (1.9), and a compost seed (1.0) which is designated Mix-1 in this work. To simplify the laboratory-scale compost weight loss test method and better understand how compost mixture compositions and environmental parameters affect the rate of plastic degradation, a systematic variation of the synthetic mixture composition as well as the moisture content was carried out. Cellulose acetate (CA) with a degree of substitution (DS) value of 1.7 and cellophane films were chosen as test polymer substrates for this work. The extent of CA DS-1.7 and cellophane weight loss as a function of the exposure time remained unchanged when the metal and glass components of the mixture were excluded in Mix-2. Further study showed that large variations in the mixture composition such as the replacement of tree leaves, food, meat, and sawdust with steam-exploded wood and alfalfa (forming Mix-C) could be made with little or no change in the time dependence of CA DS-1.7 film weight loss. In contrast, substituting tree leaves, food, meat, cow manure, and sawdust with steam-exploded wood in combination with either Rabbit Choice (Mix-D) or starch and urea (Mix-E) resulted in a significant time increase (from 7 to 12 days) for the complete disappearance of CA DS-1.7 films. Interestingly, in this work no direct correlation was observed between the C/N ratio (which ranged from 13.9 to 61.4) and the CA DS-1.7 film weight loss. Decreasing moisture contents of the compost Mix-2 from 60 and 50 and 40% resulted in dramatic changes in polymer degradation such that CA DS-1.7 showed an increase in the time period for a complete disappearance of polymer films from 6 to 16 and 30 days, respectively.Guest Editor: Dr. Graham Swift, Rohm & Haas.Paper presented at the Bio/Environmentally Degradable Polymer Society—Second National Meeting, August 19–21, 1993, Chicago, Illinois.     

高分子吸水树脂作为蓄冷材料的性能研究

本文研究了不同吸水倍率的高分子吸水树脂的相变温度、相变潜热及作为蓄冷材料在35℃环境下的相变时间,并与冰做了对比。结果显示：吸收不同倍率水的高分子树脂。相变温度和相变潜热基本与水相似,随着吸水倍率的增加,相变潜热越接近于水的潜热;在相同条件下放置于隔冷袋中的高分子吸水树脂．在35℃高温环境中,可以维持20℃以下低温5h,比冰多了将近1h,克服了渗漏的缺点,在蓄冷领域表现出了明显的优势。     

分子印迹技术在环境科学领域中的应用

分子印迹技术（MIT）是一门新兴的边缘科学技术，它的产生与发展为环境科学打开了又一视角。介绍了MIT的产生与发展及基本原理，综述了MIT在环境科学领域中的应用，主要包括MIT在固相萃取、膜分离、色谱分析、传感器及分子印迹聚合物作为催化剂在环境修复中的应用。     

生物降解高分子材料的研究现状及应用前景

目前,处理高分子材料的一些传统方法,如焚烧法、掩埋法、熔融共混挤出法、回收利用等都存在一定的缺陷和局限性,给环境保护带来严重的困难。因此,开发环境可接受的降解性高分子材料是解决环境污染的重要途径。生物降解高分子是指通过自然界或添加的微生物的化学作用,将高分子物质分解成小分子化合物,再进入自然的循环过程。论述了生物降解高分子材料的研究现状,并对生物降解高分子材料的降解机理、影响因素及其在医学、农业、包装业和其他领域的潜在应用前景进行了探讨。